Deep Patch™ is a solid concrete repair product for patching large holes in concrete surfaces. SureCrete’s solid cement filler is a single component, just add water cement based chemical patching compound system providing a patch that goes from 1/8″ (0.32 cm) to 2″ (5 cm) thickness, and up to 4″ when combined with #8 pea gravel. Deep Patch offers superior power to patch and repair larger spalls in concrete floors, building ramps, loading docks, and parking lot pavement.
DATA SHEET DOWNLOADS
Deep Patch™ is a just add water concrete patch for large concrete voids or holes. Performing well in filling low spots on horizontal surfaces and filling open areas (e.g. planters). The silicate aggregate size will cut the usual shrink cracks associated with topping mixes used for concrete repairs. Contractors and DIY homeowners alike will want to take advantage of the benefits of Deep Patch™ for their many concrete patching projects. It can give a suitable alternative to destroying old, damaged concrete and having to repair a new slab entirely. This product will allow the applicator just to remove the concrete areas that are too damaged to repair and fill in those voids instead of replacing the entire substrate.
Contractors will speed up a restoration process, as instead of having to wait 28 days for a freshly poured concrete to cure, most of all, customers can start applying a finished flooring product on top of Deep Patch™ the very next day.
- Kitchen Floors
- Bathroom Floors
- Shower Floors
- Residential Living Area Floors
- Parking Garages
- Thick Concrete Repair
- Patio Floors
- Pool Decks
- Commercial Floors
- Large Concrete Hole Repair
- Home Concrete Cracks
- Clean the surface – Concrete substrate should be completely clear of any grease, oil, old paint, etc.. Otherwise it will not form a good bond.
- While not always necessary, some areas may need profiling if they are exceptional "tightly trowelled." Easily be done with another of our Surface Preparation products - SCR.
- Dampen the surface of the concrete (no puddles, though!). Then apply a thin coating of SureBond (associated product used as a bonding agent, mixed with water, sold separately) to a small work area so as not to let it dry out.
Mix Deep Patch™ with water thoroughly in a large bucket. While working to ensure it does not set up before it can be applied.
- Apply Deep Level to ONLY the work area where SureBond is present, not dry. Continue following these steps until all sectors have been patched/covered to your satisfaction! Deep Level is typically trowelled into place; however, application methods will vary depending on the project needs.
- Patches in excess of 2” (5 cm) up to 4” (10cm) require the introduction of # 8 pea gravel (3/8 - ½” [9.5 – 12.7 mm]) at the rate of 10 pounds (4.5 kg) pea gravel to 1 – 50 pound (22.7 kg) bag of Deep Patch™.
1. Before applying Deep Patch™, the surface should be saturated surface dry with clean water (SSD or damp, no puddles).
2. Apply SureBond™ according to the TDS Deep Level
1. While SureBond™ is still wet, use Deep Level™.
2. Apply Deep Patch™ by trowel or squeegee, ensure the product is tightly placed into patched area.
By itself, we do not suggest going any thicker than 2" to repair holes. However, with small pea gravel aggregate into the mix, that may be stretched and to as much as 4". See the TDS for specific instructions on this application method
This product was not designed to be able to give a tight, feathered edge, or a finished surface. The aggregate size is quite large; the thinnest is can be applied 1/8". If a smoothing feathered repair concrete finished edge is desired, try using one of our other products such as FlashPatch™ or SureTex™ with Deep Level.
While an overnight cure of 12 hours, enough for most coatings systems, depending on the thickness that Deep Level was applied, we suggest waiting a concrete setting full 24 hours before putting any overlay or surface on top of a new Deep Level application.
Yes. However our coloring systems matching color charts have formulated based on white-cement-based products, so we cannot offer a typical color chart picking and choose the finished color from, they will almost seem different in Deep Patch™ since it is a grey-cement-based mix.
|Coverage||0.46 cubic feet per 50 lb bag|
|Shelf Life||12 months in unopened package|
|VOC Rating||0 g/L|
|Compressive Strength||ASTM C 109: 24 hours = 3,130 PSI (21,581 kPa); 28 days = 5,000 PSI (34,474 kPa)|
|Tensile Strength||ASTM C 109: 1 day = 280 PSI (1,931 kPa); 28 days = 890 PSI (6,136 kPa)|
|Flexural Strength||ASTM C 348: 1 day = 210 PSI (1,448 kPa); 28 days = 550 PSI (3,792 kPa)|
|Abrasion Resistance||grams lost @ 1/4" (0.635 cm) thickness: 24 hours = 1 gram; 7 days = 1 gram|
50 LB Bag